Difference between revisions of "Other accessories"
(Created page with "Category:Hardware {| align="right" | __TOC__ |} === '''Tool Position Accessories''' === ==== Lasers ==== Hot-swappable Lasers are available in the following configurati...") |
(→Lasers) |
||
(4 intermediate revisions by the same user not shown) | |||
Line 4: | Line 4: | ||
|} | |} | ||
− | + | Accessories other than print heads are available, some of which take a tool position. | |
− | == | + | == '''Tool Position Accessories''' == |
− | + | The following accessories are loaded into tool positions on the yoke: | |
− | + | === Lasers === | |
− | |||
− | + | See [[Lasers]]. | |
− | + | === Spindle Tools === | |
− | |||
− | |||
<gallery> | <gallery> | ||
Line 25: | Line 22: | ||
Intended for light drilling and routing operations (especially circuit board work), the ST1 provides between 500 and 5000 RMP (depending on load) to a 1/8" chuck. Our Repetrel software can process Gerber and DRL files for the Spindle Tool and/or the Lasers. | Intended for light drilling and routing operations (especially circuit board work), the ST1 provides between 500 and 5000 RMP (depending on load) to a 1/8" chuck. Our Repetrel software can process Gerber and DRL files for the Spindle Tool and/or the Lasers. | ||
− | + | == '''Other Tool Position Accessories''' == | |
− | The following accessories each take up a tool position while performing more | + | The following accessories each take up a tool position while performing more ancillary functions: |
* The Inspector microscope provides magnification. | * The Inspector microscope provides magnification. | ||
Line 33: | Line 30: | ||
* The Tramming Tool, provided with every printer, is used to level the build surface. | * The Tramming Tool, provided with every printer, is used to level the build surface. | ||
− | + | == '''Non-Tool Position Accessories''' == | |
− | The following | + | The following accessories are not loaded into tool positions on the yoke: |
+ | * The HTC - Enclosure Heater with Temperature Control is avialable in 120 and 240 VAC versions. [[:File:Htc.jpg|Spec Sheet]] | ||
* The Feed Chamber Cooling Fan mounts on Hot Flow heads to provide additional cooling to the feed chamber. This is desirable with low temperature filaments like PLA. | * The Feed Chamber Cooling Fan mounts on Hot Flow heads to provide additional cooling to the feed chamber. This is desirable with low temperature filaments like PLA. | ||
* The Printer Support Kit is included with every printer, and includes a build plate, blue tape, and a variety of handy tools like tweezers, razors, and a spatula. | * The Printer Support Kit is included with every printer, and includes a build plate, blue tape, and a variety of handy tools like tweezers, razors, and a spatula. | ||
− | * The SDK | + | * The SDK - Software Developer's Kit provides hardware, software, and the source code for developing your own firmware for your own compatible heads. |
− | * The LTK | + | * The LTK - Luer Tip Kit provides an EMO to Luer adapter and a variety of luer lock needles. |
* The Syringe Kit provides syringes in quantity. | * The Syringe Kit provides syringes in quantity. | ||
* The Drill Bit Kit provides an assortment of drilling bits and end mills for the Spindle Tool. | * The Drill Bit Kit provides an assortment of drilling bits and end mills for the Spindle Tool. | ||
* The Filament Kit provides a variety of filaments to get you started with your printer. | * The Filament Kit provides a variety of filaments to get you started with your printer. |
Revision as of 14:20, 13 October 2017
Accessories other than print heads are available, some of which take a tool position.
Tool Position Accessories
The following accessories are loaded into tool positions on the yoke:
Lasers
See Lasers.
Spindle Tools
Intended for light drilling and routing operations (especially circuit board work), the ST1 provides between 500 and 5000 RMP (depending on load) to a 1/8" chuck. Our Repetrel software can process Gerber and DRL files for the Spindle Tool and/or the Lasers.
Other Tool Position Accessories
The following accessories each take up a tool position while performing more ancillary functions:
- The Inspector microscope provides magnification.
- The Quiet Storm fan provides additional cooling.
- The Tramming Tool, provided with every printer, is used to level the build surface.
Non-Tool Position Accessories
The following accessories are not loaded into tool positions on the yoke:
- The HTC - Enclosure Heater with Temperature Control is avialable in 120 and 240 VAC versions. Spec Sheet
- The Feed Chamber Cooling Fan mounts on Hot Flow heads to provide additional cooling to the feed chamber. This is desirable with low temperature filaments like PLA.
- The Printer Support Kit is included with every printer, and includes a build plate, blue tape, and a variety of handy tools like tweezers, razors, and a spatula.
- The SDK - Software Developer's Kit provides hardware, software, and the source code for developing your own firmware for your own compatible heads.
- The LTK - Luer Tip Kit provides an EMO to Luer adapter and a variety of luer lock needles.
- The Syringe Kit provides syringes in quantity.
- The Drill Bit Kit provides an assortment of drilling bits and end mills for the Spindle Tool.
- The Filament Kit provides a variety of filaments to get you started with your printer.