Search results

Jump to: navigation, search

Create the page "2 Install" on this wiki! See also the search results found.

  • Main Page
    '''[[Repetrel_Download|Repetrel version 4.2.596 is available here!]]''' 2. Compare our various accessories with '''[http://hyrel3d.net/wiki/index.php
    3 KB (531 words) - 10:40, 6 July 2023
  • 3 Install
    ...o be on the latest version 3 release. You are welcome to remain on version 2 (or even 1), but we will only be able to provide limited support (and no bu <br>2. [[Ecosystem_Apps]]
    3 KB (422 words) - 15:33, 9 September 2021
  • Videos
    | Cleaning the Hyrel 3D DMH-2 Dynamic Mixing Head | Cleaning Hyrel 3D's DMH-2 Dynamic Mixing Head
    44 KB (7,247 words) - 18:39, 12 March 2024
  • Repetrel
    This page describes and explains the Repetrel software. To download and install the software, please see the [[Downloads]] page. ...rsion 4.x was first released in August 2019; as of March 2023, we are on 4.2.5xx
    46 KB (7,506 words) - 12:42, 11 May 2023
  • Filament Heads OLD
    ...Non-Hydra units shipping through spring 2017 shipped with Repetrel version 2.x. ...ed to 3.x when it is available. If you run a head with v2 settings on a v3 install, the background will flash red; please make the changes below, from red to
    6 KB (841 words) - 16:27, 15 July 2020
  • Installing Elsewhere
    # Install the latest repetrel from [[https://hyrel3d.com/wiki/index.php/Repetrel_Down 2. Install the software as shown at [[Software#Repetrel_.26_Firmware_-_Version_2.855_a
    4 KB (680 words) - 15:13, 24 January 2024
  • Firmware
    ...g 2017 shiped with Repetrel version 2.x, and should be on the last version 2 release. ...when it is available. If you run a head with v2 settings on a v3 or later install, the background will '''<span style="color: red;">FLASH RED</span>'''; this
    13 KB (2,149 words) - 17:28, 22 November 2023
  • Repetrel Download
    The new Repetrel installer will also install the prerequisites, so the process is: <br> 2. [[Firmware]] on Motion Controller as well as head/bed controllers
    5 KB (746 words) - 18:58, 22 January 2024
  • Settings
    ...table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under <code>C:\Users\ | <code>C:\EcosystemApps\GIMP 2\bin\gimp-2.8.exe</code>
    6 KB (1,037 words) - 15:36, 1 February 2024
  • Overview
    ...ore in-depth look, please see the '''[[Repetrel]]''' page. To download and install, please see the '''[[Software]]''' page. ! style="width: 10%" rowspan="2"|Designation
    6 KB (987 words) - 18:24, 23 February 2021
  • Ecosystem Apps
    ...are required, and will be called from Repetrel to manipulate a file. This install should all be carried out per the instructions below, so that Repetrel will ...table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under <code>C:\Users\
    2 KB (355 words) - 15:39, 8 April 2020
  • Reservoir Heads OLD
    ...ed to 3.x when it is available. If you run a head with v2 settings on a v3 install, the background will flash red; please make the changes below: | <span style="color: red;">Values for versions 1.x and 2.x will be inicated in RED.</span>
    28 KB (3,986 words) - 16:28, 15 July 2020
  • How do I...
    Note, if you set park for head 4, then head 2 will be 70mm off. Each position is 35 *mm from the next. *70 mm between fir 2. Record the absolute X and Y positions:
    31 KB (5,319 words) - 14:08, 13 March 2024
Retrieved from "https://hyrel3d.com/wiki/index.php/Special:Search"