Difference between revisions of "Materials"

From Hyrel3D
Jump to: navigation, search
Line 12: Line 12:
 
! Extruder
 
! Extruder
 
! HotHead (°C)
 
! HotHead (°C)
! Fan Speed
+
! Fan Speed*
 
! HotBed (°C)
 
! HotBed (°C)
 
! Steps / nl
 
! Steps / nl
Line 81: Line 81:
 
|-
 
|-
 
|}
 
|}
 +
 +
*Note: Be sure the fan directs air to the material and not directly at the nozzle.
 +
*Note: In Repetrel 1.85, you should slice with a fan value between 0 and 39, which will result in a fan speed between 0 and 99, since we have our fans run between 0 and 100, not between 0 and 255 like other printers.

Revision as of 18:14, 28 April 2015


A huge variety of materials can be printed with various extruders on the Hyrel machines. Below are the recipes we have so far...

Materials Printable on Hyrel Machines

The following is a list of materials with which the Hyrel machines can print; you can sort by any column:

Material Reference Chart
Material Extruder HotHead (°C) Fan Speed* HotBed (°C) Steps / nl Verified?
ABS MK1-250 240/235 35 (=89%) 80 0.78 yes
PLA MK1-250 185/180 35 (=89%) 40 0.78 yes
PlastInk Rubber MK1-250 225 35 (=89%) 50 0.78 yes
NinjaFlex MK1-250 225 35 (=89%) 50 0.78 yes
Nylon MK1-250 225 35 (=89%) 80 0.78 yes
T-Glase MK1-250 225 35 (=89%) 80 0.78 yes
BendLay MK1-250 225 35 (=89%) 50 0.78 no
LayBrick MK1-250 225 35 (=89%) 80 0.78 no
LayWoo-d3 MK1-250 220/205 35 (=89%) 80 0.78 yes
PET MK1-250 210 35 (=89%) 40 0.78 no
PVA MK1-250 210 35 (=89%) 40 0.78 no
Clay EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
Metal Clay,
Precious Metal Clay
EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
Polypropylene MK1-250 235 35 (=89%) 80 0.78 yes
Polycarbonate MK1-350 350 35 (=89%) 80 0.78 yes
Porcelain EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
Plasticine EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
Plah-Doh EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
Sculpey EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
Sugru EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
RTV Silicone EMO-25, 19:1
EMO-25, 27:1
n/a n/a n/a 1.75
2.30
yes
  • Note: Be sure the fan directs air to the material and not directly at the nozzle.
  • Note: In Repetrel 1.85, you should slice with a fan value between 0 and 39, which will result in a fan speed between 0 and 99, since we have our fans run between 0 and 100, not between 0 and 255 like other printers.