Difference between revisions of "Firmware"
(→Print Head / Hot Bed Firmware) |
(→Download 150px|link=http://hyrel3d.net/downloads/firmware/Firmware_2017.05.10.rar) |
||
| Line 8: | Line 8: | ||
There are two families of firmware; one for the heads, or STM-103 boards, and another for the motion controllers, or STM-427 / STM-407 boards. | There are two families of firmware; one for the heads, or STM-103 boards, and another for the motion controllers, or STM-427 / STM-407 boards. | ||
| − | |||
| − | |||
| − | |||
| − | |||
== Print Head / Hot Bed Firmware == | == Print Head / Hot Bed Firmware == | ||
Revision as of 20:18, 9 July 2018
New software will often require new firmware. New software packages always come with the latest firmware at the time the software was released; however, sometimes newer firmware is available.
There are two families of firmware; one for the heads, or STM-103 boards, and another for the motion controllers, or STM-427 / STM-407 boards.
Print Head / Hot Bed Firmware
For the STM-103 Boards. Consult the table below for the proper version. The wrong version WILL NOT WORK.
Video instructions for flashing the 103 (HH/HB) Controllers: https://youtu.be/yM8QMZBTb4o
- Launch Repetrel ( C:\Repetrel\bin\Repetrel.exe ).
- Go to File > Update Firmware > Motion Controller
- Select the latest .dfu file for your machine from the table above.
- Your printer should show as "CONNECTED" in the firmware utility. If it is not:
- Access the Motion Controller.
- Change the vertical switch to BOOT CONFIG (away from the vertical switch).
- Reset the motion controller (small button left of the LED).
- You should now be CONNECTED.
- Click "Program" - the process takes a few seconds.
- IF you had to change the switch, change it back and reset the motion controller.
- You are done.
You should not have to flash new firmware on any heads, although some values have changed; please see the charts at Cold and Warm Flow and Hot Flow for details.
| Filament Heads | Firmware |
|---|---|
| MK1-250 | _FIL_250_PLAT_1A.hex |
| MK1-250 with red RTDs (from 2013, 2014) | _FIL_250_RED_235A.hex |
| MK2-250 | _FIL_250_PLAT_1A.hex |
| MK1-450 | _FIL_450_45A.hex |
| Emulsion-Type Heads | Firmware |
| All Emulsion-type Heads (including mixing heads) | _TUBES_35K.hex |
| With COD or Clench Valve tied to Printing Moves Only | _TUBES_49V.hex |
| Laser Heads | Firmware |
| Diode Lasers on Repetrel v2.x | _LASER_R2_234.hex |
| Diode and CO2 Lasers on Repetrel v3.x | _LASER_R3_PWM_6L.hex |
| Spindle Tools | Firmware |
| Spindle Tools (1- and 3- Phase) | _DrillMill_2.3.hex |
| Inkjet Heads | Firmware |
| Inkjet Headss (Heat- and Piezo- based) | _INKJET_6E.hex |
Motion Controller Firmware
For the STM-429 and STM-407 Boards
Video instructions for flashing the 103 (HH/HB) Controllers: https://youtu.be/yM8QMZBTb4o
| Printer Model | Repetrel Version | Firmware |
|---|---|---|
| All Hydra Models (3-, 4- and 5- axis) | Repetrel 3.07x | Hydra 3.07x |
| Engine, High Resolution | Repetrel 3.07x | Hydra 3.07x |
| System 30M (and earlier Systems) | Repetrel 3.07x | Hyrel 3.07x |
| Repetrel 2.865 | Version 2.414 | |
| Engine, Standard Resolution | Repetrel 3.07x | Hyrel 3.07x |
| Repetrel 2.865 | Version 2.414 |
