Difference between revisions of "Emulsifiables"

From Hyrel3D
Jump to: navigation, search
Line 4: Line 4:
 
| __TOC__
 
| __TOC__
 
|}
 
|}
 +
 +
== Overview ==
  
 
EMO-Type heads are for printing as follows:
 
EMO-Type heads are for printing as follows:
Line 46: Line 48:
  
 
As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.
 
As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.
 +
 +
== Settings ==
  
 
Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:
 
Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

Revision as of 20:29, 16 December 2015

Overview

EMO-Type heads are for printing as follows:

  • With pastes, gels, emulsifiables or waxes.
  • At room or elevated temperatures.
  • With or without UV Crosslining.
  • With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

These include the following:

EMO-Type Head Comparison
Temperature Ambient Up to 100°C Up to 150°C
No Crosslinking EMO-25

SDS-5, -10, -30, -60

VOL-25 KRA-15
With Crosslinking COD-25

CSD-5, -10, -30, -60

VCD-25 KCD-15

So, what do these goofy designations actually stand for?

EMO: Emulsifiables at Room Temperature
COD: Emulsifiables T Room Temperature with Crosslink On Demand
VOL: Volcano: Heated (up to 100°C) Emulsifiables
VCD: Volcanic Crosslink on Demand
KRA: Krakatoa: Heated (up to 150°C) Emulsifiables
KCD: Krakatoic Crosslink on Demand
SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature)
CSD: Crosslinking Syringe Dispensing System

As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.

Settings

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

EMO-Type Head Comparison
Settings EMO, VOL, KRA, COD, VCD, KCD Heads
(17mm Tubes, Various Gear Ratios)
SDS, CSD Heads
(Various Tube Diameters, Standard Gear Ratios)
19:1 Ratio 27:1 Ratio 51:1 Ratio 100:1 Ratio SDS-5 SDS-10 SDS-30 5SDS-60
Material
Type Plasticine Plasticine Plasticine Plasticine Plasticine Plasticine Plasticine Plasticine
Color (any) (any) (any) (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600 1.600 1.600 1.600
Layer 300 300 300 300 300 300 300 300
Temp Info
Print Temp 30 30 30 30 0 0 0 0
Power Factor 100 100 100 100 100 100 100 100
Minimum 0 0 0 0 0 0 0 0
Maximum 0/100/150 0/100/150 0/100/150 0/100/150 0 0 0 0
Overrides
Pulses 1.600 2.300 4.700 8.500 0.750 0.750 TBD TBD
Feed Rate % 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
Prime
Steps 500 700 900 2000 300 300 TBD TBD
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 110 120 100 100 TBD TBD
Before Tool Change 1 1 1 1 1 1 1 1
Unprime
Steps 400 550 750 1600 300 TBD TBD TBD
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 100 110 100 100 TBD TBD
After Tool Change 1 1 1 1 1 1 1 1
Offsets
Clone Head Off Off Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies)
RTD Type 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg
Motor Current High High High High High High High High
Step Mode Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth